| High-temperature silicone sealant Masuma is used for local repair and formation of gaskets in heat-loaded vehicle parts. Versatile and easy to use: does not require high precision of application, excess is easily removed from the surface. Due to its chemical neutrality, the silicone sealant is compatible with other seal materials. Free of aggressive acids and solvents, non-corrosive, suitable for sealing electrical connectors and sensors. Resistant to oils and coolants, acidic and alkaline environments Applications: engine sump and gearbox; valve cover; water pump; thermostat housing; intake manifold; electrical connectors and sensors. Properties: Meets OEM factory requirements. Temperature resistant, -60 ° ; C up to + 343 ° C. Possesses low fluidity. Resistant to shock loads and vibration. On a neutral basis (odorless). Resistant to the influence of technical fluids of the car. Resistant to temperature extremes and atmospheric influences. Allows filling a cavity up to 6 mm. Corrosion-resistant. Possesses high adhesion. Meets the specifications of manufacturers: ACURA 8718-550030; HONDA 296380, 296381, 08718-0001, 08718-55000040E, HC2963817, 0096Z-POA; MITSUBISHI MD997740, MD997110; NISSAN 7995MP-A7000-002 01281, 00295-01208; TOYOTA GB 00001-01001, 00001-01002, 08826-00080, 08826-00090 Application: Remove old sealant, moisture, oil, dirt and both Pierce the cap on the tube with the back of the cap and install the nozzle. Cut the nozzle to the required size. Apply the sealant to one of the joining surfaces around the perimeter and around the assembly holes. After 2 to 3 minutes after application, join the surfaces and assemble the part. Setting time - mdash; 10 min; curing time 12-14 hours; time of complete polymerization & mdash; 24 hours.After use, remove the nozzle from the tube and close the lid. Remove cured silicone from tip. Composition: Polydimethylsiloxane & gt; 30%. Dimethicone 5-15%. Silica (microcrystalline silicon dioxide) 5-15%. Methyltris (methylethylketoxime) silane 5-15%. Vinyltris (methyl ethyl ketoximine) silane & lt; 5%. Aminopropyltriethoxysilane & lt; 5%. | High-temperature silicone sealant Masuma is used for local repair and formation of gaskets in heat-loaded vehicle parts. Versatile and easy to use: does not require high precision of application, excess is easily removed from the surface. Due to its chemical neutrality, the silicone sealant is compatible with other seal materials. Free of aggressive acids and solvents, non-corrosive, suitable for sealing electrical connectors and sensors. Resistant to oils and coolants, acidic and alkaline environments Applications: engine sump and gearbox; valve cover; water pump; thermostat housing; intake manifold; electrical connectors and sensors. Properties: Meets OEM factory requirements. Temperature resistant, -60 ° ; C up to + 343 ° C. Possesses low fluidity. Resistant to shock loads and vibration. On a neutral basis (odorless). Resistant to the influence of technical fluids of the car. Resistant to temperature extremes and atmospheric influences. Allows filling a cavity up to 6 mm. Corrosion-resistant. Possesses high adhesion. Meets the specifications of manufacturers: ACURA 8718-550030; HONDA 296380, 296381, 08718-0001, 08718-55000040E, HC2963817, 0096Z-POA; MITSUBISHI MD997740, MD997110; NISSAN 7995MP-A7000-002 01281, 00295-01208; TOYOTA GB 00001-01001, 00001-01002, 08826-00080, 08826-00090 Application: Remove old sealant, moisture, oil, dirt and both Pierce the cap on the tube with the back of the cap and install the nozzle. Cut the nozzle to the required size. Apply the sealant to one of the joining surfaces around the perimeter and around the assembly holes. After 2 to 3 minutes after application, join the surfaces and assemble the part. Setting time - mdash; 10 min; curing time 12-14 hours; time of complete polymerization & mdash; 24 hours.After use, remove the nozzle from the tube and close the lid. Remove cured silicone from tip. Composition: Polydimethylsiloxane & gt; 30%. Dimethicone 5-15%. Silica (microcrystalline silicon dioxide) 5-15%. Methyltris (methylethylketoxime) silane 5-15%. Vinyltris (methyl ethyl ketoximine) silane & lt; 5%. Aminopropyltriethoxysilane & lt; 5%. |
